MOVMAX Blade Arm (Blue)

Movmax Blade Arm Special Blue Edition is a compact arm with N2 hydraulic damping for shooting from a car with DJI Osmo Pocket 3, Insta360 X4, GoPro HERO12 or a phone. The IMT suction cup holds from −40 to 80 °C, payload 150–500 g.

Blade Arm brings the N2 stabilising arm of Movmax’s large car mounts down to pocket size. It attaches to the bonnet, a door or the rear of a car with the IMT vacuum suction cup, and the hydraulic damping with an adjustable spring absorbs the vertical shocks a small camera cannot handle on its own. The Special Blue Edition is technically identical to the black Blade Arm and differs only in the colour of the arm body.

Smooth shots from a moving car

A hydraulically damped arm with a suction cup for DJI Osmo Pocket 3, action and 360° cameras or a phone – payload 150 to 500 g.

Payload 150–500 gHydraulic dampingIMT suction cup−40 to 80 °C1/4″-20 thread

N2 arm technology

The arm’s pivot point works together with the pull rod to absorb large vibrations in the vertical direction. Fine-tune the spring with the threaded knob.

Vacuum-pump suction cup

The large IMT suction cup holds firmly on the bonnet, doors or rear of a car and works from −40 to 80 °C.

Counterweights for your rig

Add or remove the 100 g and 50 g steel counterweights to match what you mount – from a bare Pocket 3 to a camera with a handle.

No jelly effect

A rigid mount passes body vibration straight into the camera and the picture wobbles. Blade Arm damps the vibration before it reaches the camera, so the shot stays clean even at speed.

Clutch cross shaft

More than 10× more stable than ball joints, with a much higher load capacity.

7″ bracket

Set the arm position with the handle screws at any mounting angle.

1/4″ connector

A universal locking screw for Pocket 3, an action camera or a phone holder.

Pocket-sized

The arm folds into a small package that fits in a bag with the rest of your kit.

Small but capable. The arm folds to pocket size, uses N2 Arm technology, mounts in many positions and holds with a strong suction cup.

Adjustable hydraulic damping. Hydraulics keep the motion stable and linear, and the spring is fine-tuned with a threaded knob to suit the camera weight.

N2 Arm technology. The arm’s pivot point works with the pull rod to absorb large vertical vibrations.

Clutch cross shaft structure. Compared with traditional ball joints, the joint is more than 10× more stable and carries much more.

Payload 150 to 500 g. Two steel counterweights of 100 g and 50 g extend the load range to suit the device and mounting method.

Using the counterweights. Pocket 3 with a 1/4″-20 threaded handle needs both counterweights (100 g + 50 g); Pocket 3 with the battery handle needs only 100 g.

Bracket, connector and suction cup. A 7″ bracket with unlimited mounting angles, a universal 1/4″ screw connector and an IMT vacuum-pump suction cup rated for −40 to 80 °C.

See the difference. With an ordinary mount the footage from a moving car wobbles with a jelly effect; with Blade Arm it stays sharp.

Front and rear mounting. High on the bonnet the camera films the car ahead and the driver; low at the rear it films the car following you.

Side mounting. On a door you capture the wheels and suspension at work, the driver’s face, or two cars passing or driving side by side.

Compatible devices. The arm is designed for DJI Osmo Pocket 3, Insta360 X4, GoPro HERO12 and, with a holder, a mobile phone.

What’s in the box. Blade Arm, a 1/4″ screw connector and two steel counterweights.